<\/p>\n
![\"\u56fe\u72471\"](\"https:\/\/ksensors.co.kr\/wp-content\/uploads\/2026\/01\/28_tupian1.png\" "\\"\u56fe\u72471\\"")
<\/p>\n
Features<\/strong>:<\/strong>\u00a0<\/strong><\/p>\n \u25ceT7 series torque sensor is a typical structure of non-contact torque sensor, the output signal of non contact mode, the high frequency part of the signal is filtered by the detection circuit, only the torque signal is amplified. Non contact torque sensor due to the use of the non contact work, and long service life, high reliability, less susceptible to wear, less delay, deflection and axial offset axis impact smaller, now has been widely used in cars and light vehicles, is the mainstream product of EPS sensor.<\/p>\n \u25ceThe internal use of unique non-contact mode wireless transmission torque signal output.<\/p>\n \u25ceWith good stability, high precision, good reliability and long life.<\/p>\n \u25ceCan measure dynamic torque, static torque; measurement of torque signal output and speed of high or low.<\/p>\n \u25ceWhether it has nothing to do with rotation or steering.<\/p>\n \u25ceDo not need to repeatedly adjust the zero position to continuously measure the positive and negative torque signal.<\/p>\n \u25ceSignal using digital technology, strong anti-interference.<\/p>\n \u25ceNo slip ring wear parts, high speed can run for a long time<\/p>\n \u25ceThe measuring precision of torque is independent of the rotation speed and direction.<\/p>\n \u25cePositive and negative torque, speed and power can be measured.<\/p>\n \u25ceSmall size, light weight, easy to install, can be any location, any direction of installation.<\/p>\n Working Principle:<\/strong><\/p>\n Non contact type torque sensor, the input shaft and the output shaft connected by the torsion bar, input spline shaft, output shaft with keyway. When the torsion bar by the rotation of the steering wheel torque twist, the relative position between the input shaft and the output shaft of the spline keyway is changed. The amount of relative displacement and torsion spline keyway variable is equal to the torsion bar, the spline on magnetic induction intensity changes, changes in the strength of a magnetic field, through the coil into a voltage signal.<\/p>\n Dimensions<\/strong><\/p>\n Specification<\/strong>:<\/strong><\/p>\n \u00b1\u00a00.\u00a03\u00a0%\u00a0F\u00b7S(Optional)<\/td>\n Torque signal;<\/td>\n<\/tr>\n Forward full range:15KHz;Reverse full range:5KHz;Load current<10mA<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n Application\u00a0<\/strong>R<\/strong>ange<\/strong>:<\/strong><\/p>\n \u25ceOutput torque and power of rotating power equipment such as electric motors, internal combustion engines, etc..<\/p>\n \u25ceTransfer of load torque and input power generator, fan, pump, mixer, reducer, gearbox, hoist, propeller, drilling machinery and other equipment.<\/p>\n \u25ceTransfer the torque in the process of machining center and automatic machine tool.<\/p>\n \u25ceTransmission torque and efficiency of all kinds of rotating power system.<\/p>\n \u25ceCan be used in the manufacture of viscometer.<\/p>\n Installation:<\/strong><\/p>\n \u25ceTwo end shaft extension flat key connection.<\/p>\n \u25ceThe sensor connector is divided into a. B end, B end is the measuring end, a end is the auxiliary B end which is connected with the tested equipment through the coupling, and the additional bending moment must be avoided during the installation.<\/p>\n \u25ceIf it is necessary to measure the speed, it is only necessary to install a special speed sensor and its speed measuring wheel inside the torque sensor of this series to measure the speed signal of 6-30 square waves per revolution.<\/p>\n Signal Processing:<\/strong><\/p>\n 1. Use the torque meter to directly display the torque value;<\/p>\n 2. Directly send the torque frequency signal to the computer or PLC for processing;<\/p>\n 3. The external module can be converted to 4-20mA or 1-5V analog signal;<\/p>\n Please Note for use:<\/strong><\/p>\n \u25ceWiring must be correct;<\/p>\n \u25ce\u00b115V range: not less than \u00b1 14.5V and not more than \u00b1 15.5v;<\/p>\n \u25ceThe output of signal line shall not be short circuited to ground or power, and the output current shall not be greater than 10mA;<\/p>\n \u25ceThe shielding layer of shielded cable must be connected with the common terminal (power ground) of \u00b1 15V power supply;<\/p>\n \u25ceThe elastic body of the sensor is very fine and small, and overload is strictly limited, and the overload range is\u226420%, otherwise it is very easy to be damaged;<\/p>\n \u25ceIf you have any questions in use, please contact our company in time, and do not dismantle it by yourself within the warranty period;<\/p>\n <\/p>\n![\"\u56fe\u72472\"](\"https:\/\/ksensors.co.kr\/wp-content\/uploads\/2026\/01\/29_tupian2.png\" "\\"\u56fe\u72472\\"")
<\/p>\n\n\n
\n Measuring Range<\/td>\n 0.01-5N.m<\/td>\n Use Temperature<\/td>\n \uff0d1 0\uff5e5 0 \u2103<\/td>\n<\/tr>\n \n Torque Precision<\/td>\n \u00b1 0. 5 % F\u00b7S<\/p>\n Storage Temperature<\/td>\n \uff0d20\uff5e70\u00a0\u2103<\/td>\n<\/tr>\n \n Response Frequency<\/td>\n 100 \u03bcs<\/td>\n Supply Voltage<\/td>\n \u00a0\u00b1 15V \u00b1 5 %<\/td>\n<\/tr>\n \n Nonlinear<\/td>\n \u00b1 0. 3 % F \u00b7 S<\/td>\n Load Current<\/td>\n <10mA<\/td>\n<\/tr>\n \n Zero Temperature Drift<\/td>\n \u00b1 0. 3 % F \u00b7 S<\/td>\n Relative Humidity<\/td>\n \u226495%RH<\/td>\n<\/tr>\n \n Insulation Resistance<\/td>\n >500M \u03a9<\/td>\n Suitable Speed<\/td>\n Under 6000RPM\/Min<\/td>\n<\/tr>\n \n Static Overload<\/td>\n 150%<\/td>\n Signal<\/td>\n 0V; + 15V; -15V; Speed Signal;<\/p>\n \n Self Weight<\/td>\n 1kg<\/td>\n<\/tr>\n \n Output Signal:<\/td>\n 0-12v square wave frequency; Zero torque: 10kHz;<\/p>\n ![\"\u56fe\u72473\"](\"https:\/\/ksensors.co.kr\/wp-content\/uploads\/2026\/01\/17_tupian3-500x800.png\" "\\"\u56fe\u72473\\"")
<\/p>\n